Hydroil НМ Print
Hidroil НМ         TS U 23.2-30802090-060:2006
Oil Hidroil HM is used as a working liquid for hydraulic actuators, hydraulic transmissions, and circulating oil systems of different units, low-and moderate gears and worm gears, variable, electromagnetic, and gear couplings, bearing units, sliding guides and bearings, and other sites of the machinery of modern industrial equipment. It does not contain chlorine compounds.
Index Name Hidroil HM 10 Hidroil HM 22 Hidroil HM 32 Hidroil HM 46 Hidroil HM 68 Hidroil HM 100
Meets classification ISO VG
ISO 6743 / / DIN 51524.2		 10
HM / / HLP		 22
HM / / HLP		 32
HM / / HLP		 46
HM / / HLP		 68
HM / / HLP		 100
HM / / HLP
Kinematic viscosity at 40 °С, mm² / s: 8 – 14 18 – 26 28 – 36 42 – 50 61 – 75 90 – 110
Viscosity index, not less than 108 100 98 97 94 91
Acid number, mg КОН / g, not more than 0,7
Temperature, °С:
flash point in an open crucible, not lower than
pour point, not higher than
160
– 30
170
– 27
190
– 24
200
– 24
210
– 24
220
– 18
Ash, %, not more than 0,2
Colour, units of CNT, with breeding 15 / 85, not more than 1,0 1,5
 
OILS FOR HYDRAULIC SYSTEMS Print
Agrinol I-HG-B TS U 30802090.003-2000
The oils are used as working liquids in hydraulic systems of machine equipment, automatic lines, presses, constructing, agricultural and road machines. The oils are also used for greasing of reducers of small and average loading, plain slideway and slideway bearing of engineering tools etc.
Index name Agrinol I-HG-B-32 Agrinol I-HG-B-46 Agrinol I-HG-B-68 Agrinol I-HG-B-100 Agrinol I-HG-B-220
Meets classification ISO VG
ISO 6743 (DIN 51524.2)		 32
HM (HLP)		 46
HM (HLP)		 68
HM (HLP)		 100
HM (HLP)		 220
HM (HLP)
Kinematic viscosity at 40 °С, mm² / s 29 – 35 41 – 51 61 – 75 90 – 110 198 – 288
Acid number, mg КОН / g, not more than 1,0 1,0 1,0 1,0 1,0
Temperature, °С:
Flash points in an open crucible, not lower than
Pour point, not higher than		 200
– 15		 210
– 15		 220
– 15		 225
– 15		 225
– 10
Fraction of total mass, %, not more than:
Mechanical impurities
water
None
Traces
Stability against oxidation
acid number after oxidation, mg, KOH / g, not more than		 0,3 0,4 0,4 0,4 0,5
Corrosive influence on metals withstands


AGRINOL IGP  TS U 23.2-30802090-065:2006
Agrinol oil IGP-18, -30, -38, -49 are used to lubricate high-speed gearboxes, small and moderate gears and worm gears, variable, electromagnetic, and gear couplings, bearing units, sliding guides and bearings, and other sites where required oils are oils with improved antioxidant and antiwear properties.

Index name Agrinol
IGP-18		 Agrinol
IGP-30		 Agrinol
IGP-38		 Agrinol
IGP-49
Meets classifications ISO VG
ISO 6743 (DIN 51524.2)		 32
HM (HLP)		 46
HM (HLP)		 68
HM (HLP)		 68
HM (HLP)
Kinematic viscosity at 40 °С, mm² / s 24 – 30 39 – 50 55 – 65 76 – 85
Viscosity index, not less than 90
Acid number, mg КОН / g, not more than 1,0
Temperature, °С:
flash point in an open crucible, not lower than
pour point, not higher than
180
– 15
200
– 15
210
– 15
215
– 15
Fraction of total mass, %, not more than:
mechanical impurities
water
sulfur
zink
None
Traces
1,0
0,04
Ash, %, not more than 0,2
Stability against oxidation:
acid number, mg КОН / g, not more than
2,0
Sapunification number, mg КОН / g 0,8 – 2,5


Agrinol IGP     TS U 23.2-30802090-065:2006
Agrinol IGP-72, -91, -114, -152 and -182 are used in the hydraulics of heavy press equipment. They are also used for greasing of gear-boxes, toothed and worm reducers of average loading, circulating greasing of systems of various equipment.
Index name Agrinol
IGP-72		 Agrinol
IGP-91		 Agrinol
IGP-114		 Agrinol
IGP-152		 Agrinol
IGP-182
Meets classifications ISO VG
ISO 6743 (DIN 51524.2)		 100
HM (HLP)		 150
HM (HLP)		 150
HM (HLP)		 220
HM (HLP)		 320
HM (HLP)
Kinematic viscosity at 40 °С, mm² / s 110 – 125 148 – 165 186 – 205 265 – 280 320 – 348
Viscosity index, not less than 90
Acid number, mg КОН / g, not more than 1,0
Temperature, °С:
Flash points in an open crucible, not lower than
Pour point, not higher than
220
– 15
225
– 15
230
– 15
230
– 15
240
– 15
Fraction of total mass, %, not more than:
Mechanical impurities
water
sulphur
zink
None
Traces
0,04
1,0
None
Traces
0,04
1,4
None
Traces
0,04
1,5
Ash, %, not more than 0,2
Stability against oxidation:
acid number, mg КОН / g, not more than
2,0
Saponification number, mg КОН / g 0,8 – 2,5


Agrinol IGP- 4  TS U 23.2-30802090-089:2008
Industrial Oil IGP-4 is used for lubricating high-speed gearboxes, little and half loaded gears and worm gears, variator, electromagnetic, and gear couplings, bearing boxes of slide bearings and other components that require oils with enhanced antioxidant and antiwear properties.
Index name Agrinol IGP-4
Meets classifications ISO VG
ISO 6743 (DIN 51524.2)
All-Union State Standard 17479.4		 5
HM (HLP)
I-L-S-5
Kinematic viscosity at 40 °С, mm² / s 4,0 – 6,5
Acid number, mg КОН / g, not more than 1,0
Тemperature, °С:
flash point in an open crucible, not lower than
pour point, not higher than
100
– 15
Colour, units of CNT, not more than 1,5
Ash, %, not more than 0,2
Corrosive influence on metals None
Fraction of total mass, %, not more than:
mechanical impurities
water
sulfur
zink
None
Traces
0,9
0,04


VNII NP-403     All-Union State Standard 16728-78
Industrial oil VNII-NP-403 is used as a working liquid for volumetric hydraulics of metal-cutting machines, automatical lines, individual heavy presses and other industrial equipment as well as for circulating greasing of systems of metal-cutting machines and other mechanisms.
Index name VNII NP-403
Meets classification ISO VG, ISO 6743 (DIN 51524.2)
All-Union State Standard 17479.4 – 87		 46, HM (HLP)
I-G-V-46(p)
Kinematic viscosity at 40 °С, mm² / s 41 – 51
Viscosity index, not less than 97
Acid number, mg КОН / g, not more than 0,7 – 1,0
Тemperature, °С:
flash point in an open crucible, not lower than
pour point, not higher than		 202
– 20
Stability against oxidation, not more than:
sediment, %
acid number, mg КОН / g,
None
1,30
Fraction of total mass, %, not more than:
sulphur
mechanical impurities
water
1,0
0,007
Traces
 
For rolling mills Print
ROLLING GR      TS U 23.2-30802090-086:2008
Rolling GR S — summer lubricant, Rolling GR W — winter lubricant.
Rolling GR are industrial lubricants intended for centralized greasing systems of rolling mills, blast furnaces and other large equipment of metallurgical enterprises.
Rolling GR S is a summer lubricant, and Rolling GR W is a winter lubricant.
SLIDING GR     TS U 23.2-30802090-084:2008
Lithium lubricants for rolling mills Sliding GR are intended for greasing rolling work bearings of rolling mills, heavy duty roller and ball bearings units of industrial equipment. Lubricant Sliding GR1 is used in centralized systems of continuous greasing. Lubricant Sliding GR2 is used as a mortgage one.
Index name Rolling GR S Rolling GR W Sliding GR 1 Sliding GR 2
Meets classifications NLGI
DIN 51502		 2
К2С-0		 0 / 1
К 0 / 1 D-10		 1
KP1P-20		 2
KP2P-30
Thickener Са Li
Operating temperature, min…max, °С  + 10 … + 80 – 10 … + 80 – 20 … + 150
Dropping point, °С, not lower than 95 92 250 260
Penetration at 25 °С, mm·10 – 1 270 – 310 310 – 360 290 – 325 260 – 290
Proof strength at 50 °С, Pа, not less than 130 100 100 – 420 140 – 640
Colloid stability, %, not more than 10 12 7 6
Water-resistance, class, not lower than: – 1в
Efficient viscosity at the average gradient of the strain rate of 10 s–1, Pа•s, not more than 250 (0 °С) 200 (0 °С) 1600 (–20 °С) 2000 (–20 °С)
Tribological characteristics on Four-ball machine at (20 ± 5) °С:
Welding loading, N, not less than
Critical loading, not less than
Scuff index, N, not less than
Deterioration index (196Н), mm, not more than
1960
980
400
0,6
3283
980
440
0,40


Agrinol Termostan      TS U 23.2-30802090-032:2006
Agrinol Termostan is a heat-resistant lubricant for heavily loaded friction unit that is used as a greasing material for frictionless bearings of average and low speed and other friction units exploited at elevated temperature and loading rolling mill rolls, founding equipment, calcinators and thermal furnaces etc. It also can be used in a short-term period at the temperature not higher than 280 °С if the unit is hermetic. The lubricant should be placed into friction units manually by the method of laying or by greasing attrition faces.
Agrinol LKS     TS U  23.2-30802090-084:2008
Agrinol LKS is a lubricant intended for greasing frictionless bearings of metallurgical equipment.
Index name Agrinol Termostan Agrinol LKS
Meets classification NLGI, DIN 51502 2 КF2U-20 1 / 2 KPF 1 / 2 P-30
Thickener k-Li k-Li
Operating temperature, min…max, °С – 20 … + 230 ( + 280) – 30 … + 150 ( + 170)
Dropping Point, °С, not lower than 260 200
Penetration at 25 °С, mm·10 – 1 250 – 300 250 – 320
Proof strength at 50 °С, Pа, not less than 300 150 – 600
Colloid stability, %, not more than 5 12
Water-resistance, penetration change, mm·10 – 1 index: 1b  + 60
Effective viscosity. (at the average gradient of the strain rate of 10 s–1), Pа·s, not more than 1500 (0 °С) 2500(-20 °С)
Tribological characteristics on Four-ball machine at (20 ± 5) °С, N, not less than:
Welding loading, N, not less than
Critical loading, not less than
Scuff index, N, not less than
Deterioration index (196N), mm, not more than

6174
980
750
0,7

2764
784
400
–


Agrinol ProkatOl         TS U 23.2-30802090-004:2002
High-temperature complex calcium lubricants for centralized greasing systems of rolling mills, blast furnaces and large-size industrial equipment.
Agrinol ProkatOl-2 is a lubricant used for greasing mechanisms with open and semi-open friction units working at heavy specific loading by the method of laying.
Agrinol ProkatOl-0 is used for lubricating friction units of metallurgical mechanisms with the help of centralized greasing means.
Agrinol ProkatoL (ЕR 2)          TS U 23.2-30802090-045:2005
Agrinol Prokatol (ЕR 2) is intended for greasing friction units of rolling mills, blast furnaces and other large-size equipment of metallurgical enterprises. The lubricant contains special anti-friction additives which improve the lubricant’s anti-deterioration properties. The lubricant is placed by the method of laying.
Index name Agrinol ProkatOl-2 Agrinol ProkatOl-0 Agrinol Prokatol ER 2
Meets classifications NLGI, DIN 51502 1 / 2, KP 1 / 2 P-10 0 / 1, KP 0 / 1 P-20 1 / 2, KP 1 / 2 P-10
Thickener k-Са
Operating temperature, min…max, °С – 10 … + 150 ( + 170) – 20 … + 150 ( + 170) – 10 … + 150 ( + 170)
Dropping Point, °С, not lower than 230 230 245
Penetration at 25 °С, мм·10 – 1 265 – 320 320 – 380 265 – 320
Proof strength, at 50 °С, Pa, not less than 200 100 – 600 200
Colloid stability, %, not more than 9,0 12,0 8
Effective viscosity. (at the average gradient of the strain rate of 10 s–1), Pа·s, not more than 160 (0 °С) 110 (0 °С) 220 (0 °С)
Tribological characteristics at (20 ± 5) °С, N, not less than:,
Welding loading, N, not less than
Critical loading, not less than
Scuff index, N, not less than
2323
980
392
4900
1381
650


Agrinol IP-1     TS U 30802090.002-2000
Agrinol IP-1l (summer) and Agrinol IP-1z (winter) are hydrated fat anti-friction water-resistant lubricants which are used for centralized greasing systems of rolling mills, blast furnaces and other large-size equipment of metallurgical enterprises. The lubricants are intended for greasing friction units of industrial equipment functioning at average and heavy loading.
Agrinol Uniol-2M         TS U 23.2-30802090-087:2008
Lubricants for rolling mills Agrinol Uniol-2M are used for greasing rolling mills, blast furnaces and other large equipment of metallurgical enterprises. Lubricant Agrinol Uniol-2M-1 is used for embedded parts greasing, and lubricant Agrinol Uniol-2M-2 — is used for greasing with the help of centralized lubrication methods.
Index name Agrinol
IP-1l		 Agrinol
IP-1z		 Agrinol
Uniol-2М-1		 Аgrinol
Uniol-2М-2
Meets classifications NLGI, DIN 51502 1 / 2, К 1 / 2 С-0 0 / 1, К 0 / 1 D-10 1 KP1P-20 2 KP2P-30
Thickener Са к-Са
Operating temperature, min…max, °С  + 10 … + 80 –10 … + 80 –10… + 150 ( + 170) –20… + 150 ( + 170)
Dropping point, °С, not lower than 95 92 230
Penetration at 25 °С, мм·10 – 1 270 – 310 310 – 360 265 – 320 320 – 380
Proof strength at 50 °С, Pа, not less than 130 100 200 100 – 600
Colloid stability, %, not more than 10 12 7 6
Efficient viscosity at the average gradient of the strain rate of 10 s–1, Pа•s, not more than 250 (0 °С) 200 (0 °С) 160 (0 °С) 110 (0 °С)
Tribological characteristics on Four-ball machine at (20 ± 5) °С, N, not less than,
Welding loading, N, not less than
Critical loading, not less than
Scuff index, N, not less than		 –

2323
980
392


KLS ROLLING  TS U 23.2-30802090.033:2006
Rolling KLS-1 and Rolling KLS-2 are used for greasing frictionless bearings of rolling mill working rolls. Rolling KLS-1 is used in centralized systems of continuous greasing, and Rolling KLS-2 is used as initial lubricant.
It is permitted to utilize the lubricants for roller and ball bearings of units of other industrial equipment which should correspond to the high standards of mechanical and thermal stability under the influence of increased loading and temperature.
Agrinol LS-1 P TS U 23.2-30802090-070:2001
The lubricant is used for greasing the industrial equipment friction, operating at medium and high loads: a heavy-duty friction casting, forging and other equipment with a centralized supply system.
Index name KLS-1 rolling KLS-2 rolling Agrinol LS-1P
Meets classification NLGI, DIN 51502 1, KP1P-20 2, KP2P-20 1, KP1N-40
Thickener к-Li Li
Operating temperature, min…max, °С – 20 … + 150 – 40 … + 130
Dropping Point, °С, not lower than 250 260 185
Penetration at 25 °С, mm·10 – 1 290 – 325 260 – 290 310 – 340
Proof strength, at 50 °С,Pa, not less than 100 – 420 140 – 640 1,0 (20 °С)
Colloid stability, %, not more than 7 6 25
Efficient viscosity at the average gradient of the strain rate of 10 s–1, Pа·s, not more than 1600 (– 20 °С) 2000 (– 20 °С) 100 (20 °С)
Tribological characteristics on Four-ball machine at (20 ± 5) °С, N, not less than
Welding loading, N, not less than
Critical loading, not less than
Scuff index, N, not less than
3283
980
440
2240
1000
372
 
For film-lubrication bearings Print
Agrinol PGT       TS U 23.2-30802090-008–2002
Agrinol PGT Oils are intended for greasing of fluid friction bearings of rolling mills equipped with circulating systems with pipe-lines of various length and branching with possible irrigation.
Index name Agrinol
PGT-46		 Agrinol
PGT-220		 Agrinol
PGT-460
Meets classifications ISO VG DIN 51517.1,51517.2 46 С, CL 220 С, CL 460 С, CL
Kinematic viscosity at 40 °С, mm² / s 42 – 50 200 – 240 420 – 510
Viscosity index, not less than 95 90 90
Acid number, mg КОН / g, not more than 0,05 0,05 0,05
Тemperature, °С:
flash point in an open crucible, not lower than
pour point, not higher than
180
– 10
220
– 10
240
– 10
Coking ability, %, not more than 0,2 0,5 1,0
Demulsifying properties:
emulsion stratification time, min, not more than
volume of layers: oil-water-emulsion, cm3
20
41 – 37 – 2
20
41 – 37 – 2
30
41 – 37 – 2
Stability against oxidation, not more than:
changing of viscosity, %
changing of acid number, mg, КОН / g
5
0,1
10
0,15
10
0,4
Sulfur fraction of total mass, %, not more than 0,6 0,6 0,6
Tribological characteristics on Four-ball machine at (20 ± 5) °С:
deterioration index at loading of 196 N, mm, not more than
0,75
0,75
0,75
 
Cylinder oils Print
Light Cylinder oils Agrinol C     TS U 23.2-30802090-046:2005
Light Cylinder oils Agrinol C – petroleum oils are intended for greasing of steam engines, working in superheated steam with heavy loading and low speed.

HEAVY CYLINDER OILS 38, 52           All-Union State Standard 6411-76
Petroleum oils are intended for greasing of the reciprocating steam engines of different purposes, working in superheated steam (C-38 up to 350°C, C-52 up to 400°C) with heavy loading at low speed.
Index name Cylinder
OIL 38		 Cylinder
OIL 52		 Agrinol
C 11		 Agrinol
C 24
Kinematic viscosity at 100 °С, mm² / s 32 – 50 50 – 70 9 – 13 20 – 28
Viscosity index, not less than 60 80 55 28
Temperature, °С:
flash point in an open crucible, not lower than
pour point, not higher than
300
– 17
310
– 5
215
5
240
20
Fraction of total mass, %, not more than:
mechanical impurities
water
water-soluble acids and alkalis
None
0,05
None
0,07
0,05
None
0,007
None
None
0,05
Traces
None
Acid number, mg КОН / g, not more than 0,4 0,2 0,3 0,15
Coking ability, %, not more than 2,5 0,7 2,2
Ash, %, not more than 0,015 0,01 0,03 0,03
Corrosive influence on metals Withstands
 
More...